PX6000-I
Diffused Semiconductor Pressure Transmitter
See All Models Below
-
High Reliability
-
Long Term Stability
-
All Stainless Steel Case
-
Vacuum Range Available
-
5 Point NIST Traceable Certificate Included
Applications
-
Automotive Test
-
Research & Development
-
Engineering Test & Evaluation
-
Production Testing
-
Flight Recorders
-
Engine Monitoring
-
Ground Support Equipment
-
Built-In Temperature Sensor
Pressure Transducers - View related products
Description
This item is being discontinued.
OMEGA's PX6000 Series pressure
transducers fit easily into many
applications. These low-cost
transducers are small and light, and
mounting requires no bulky structures.
Users can select from 3 electrical
terminations and 6 pressure fittings.
The sensor is a small [about 2.54 mm
(0.1") square] silicon chip, with 4
diffused strain gages mounted in the
stainless steel case. Laser-trimmed
resistors provide temperature
compensation and adjust zero
balance and span. The 4 to 20 mA
output easily interfaces with most
control and data acquisition systems.
The PX6000 uses solid state media
isolation for improved reliability.
Thin films of chemically inert materials are deposited or grown on
the chip surface to provide electrical
isolation between the sensor and
pressure medium. The sensor is
less sensitive to vibration and
more dependable in high-shock
environments because the films
add no significant mass. Corrosion
resistance is outstanding, and the
isolation will remain effective
because there are no gel or oil
columns to deteriorate.
The PX6000 is also available in metric configurations, with G1/4 or G1/8 ports, and models
from 0-1 to 0-25 bar pressure ranges.
Please see the PXM6000 for complete details, or contact our Pressure department for more information..
SPECIFICATIONS
4 to 20 mA Models
Excitation: 12 to 40 Vdc unregulated
Output: 4 to 20 mA adjustable ±10% FS
Load Impedance (Max): 50 x (V - 10) Ω where V = supply voltage (40 Vdc max)
Zero Balance: 4 mA adjustable ±10% FS
Dielectric Isolation Resistance: 100 MΩ minimum at 45 Vdc applied between the case or a conductive medium and the bridge circuit
Sensing Element: 4-active-arm bridge using a micromachined diffused silicon diaphragm sensor, thin-film media and dielectric isolation barriers
Temperature Sensor: Output resistance @ 24°C (75°F) 900 to 1500
Temperature Coefficient: 8% min, 10% max per 55.5°C (100°F)
Accuracy: Combined linearity, hysteresis and repeatability ≤±0.25% FS for all ranges
Operating Temp Range: -29° to 85°C (-20° to 185°F)
Compensated Temp Range: -29° to 85°C (-20° to 185°F)
Thermal Effects:
Span: ≤±0.02% of FS/°F.
Zero: ≤±0.02% of FS/°F
Vibration Sensitivity: At 20 g peak sinusoidal vibration from 10 Hz to 2000 Hz (½" D.A.), the output shall not exceed 0.04% FS/g for 15 psi range to 0.005% FS/g for 100 psi and above
Natural Frequency: Greater than 35 kHz for 100 psi and above
Shock: 100 g, 11 ms half sine wave without damage
Proof Pressure: 2 times rated pressure will not cause changes in performance beyond the specified tolerances
Burst Pressure: 3 times rated pressure for pressure ranges below 200 psi, or 2.5 times rated pressure for pressure ranges above 200 psi, will not cause rupture of the pressure sensor
Wetted Parts: 316 stainless steel, silicon, Pyrex® glass, epoxy, Kovar®
Electrical Connection: PTIH-10-6P (standard), 0.6 m (2') cable or 4-pin solder terminal header (optional)
Pressure Port: MS33656-4 male (std)
Optional: MS33649-4 female, ¼-18 or 1⁄8-27 NPT male or female
Weight: 170 g (6 oz) typical
Mating Connector: PTS06A-10-6S (not included)
