Toll-Free in Philippines: 1 800 8908 8267 | 1 800 1441 0877
International+65 6415 5353

4-Channel RTD Input Data Acquisition Module with USB or Ethernet Interface


4-Channel RTD Input Data Acquisition Module with USB or Ethernet Interface | PT-104A

PHP62,112.02 PT-104A

  • Measures Temperature (RTDs), Resistance and Voltage
  • High Accuracy (0.01°C) and Resolution (0.001°C)
  • Powered by USB Port or Power-Over-Ethernet (PoE)
  • For Use with 2, 3 and 4-Wire Pt100 and Pt1000 RTD Sensors
USB, RS232, RS485 and Ethernet Data Acquisition Systems - View related products


The PT-104A is a four-channel, high-resolution temperature data acquisition module for use with PT100 and PT1000 RTD sensors. It can also be used to measure resistance (375 Ω and 10,000 Ω ranges) and voltage (115 mV or 2.5 V ranges). In PT100/PT1000/ resistance mode, the unit uses a four wire circuit. In voltage mode, the input connector can be treated as a differential input with ground, or two single-ended inputs. Both inputs must be 0V or above, though it does not matter which input has the higher voltage. For the 115 mV voltage range, the accuracy may vary by 2%, and the temperature coefficient will be 100 ppm/°C.

Although accurate temperature sensors are widely available, it has been difficult to take advantage of them due to errors caused by the measuring device. The PT-104A, however, is designed to be inherently accurate. Rather than relying on voltage references (which tend to be temperature sensitive) it uses ‘reference’ resistors which are extremely stable (low temperature coefficient and drift). The exact value of each resistor is stored in an EEPROM to provide the ultimate in accuracy (yearly re-calibration is recommended). To achieve the 0.001°C resolution a highlyadvanced ADC is used that can resolve to better than 1 part in 16 million.

The PT-104A measures temperature using platinum resistance temperature sensors (RTDs). Both common industry standards (PT100 and PT1000) are supported. The unit is compatible with 2, 3 and 4 wire sensors (4 wire PT100 sensors are recommended for accurate measurements).

When measuring resistance, the unit uses a four-wire circuit to give the greatest possible accuracy. Two resistance ranges are available (0 to 375 Ω and 0 to 10,000 Ω). The unit is calibrated for 0 to 375 ? so this range should be used for accurate measurements.

For voltage measurements, each input connector can be treated as a differential input with ground, or two single-ended inputs. Both inputs must be zero volts or above, though it does not matter which input has the higher voltage. Two voltage ranges are available (0 to 115 mV and 0 to 2500 mV). For the most accurate measurements use the 0 to 2500 mV range

Remote Data Collection
The new USB/Ethernet interface allows the logger to be used in a variety of situations: USB-only, USBpowered with Ethernet data, and Ethernet data with Power-over- Ethernet (PoE). Using the Ethernet interface, the PT-104A can be located anywhere on a LAN or on the internet.

Power over Ethernet (PoE)
The PT-104A can obtain its power from the Ethernet port as a Powered Device (PD) according to the PoE standard. To use this feature, you must connect the unit to Power Sourcing Equipment (PSE) such as a network switch, router or power injector that also supports the PoE standard. Any standard Ethernet cable up to 100 m (about 328') in length can be used.

The PT-104A is supplied with Windows Logging and Player Software. The software will automatically detect which sensor is connected and will display readings in the correct units. Also supplied is a software development kit (SDK). The SDK contains a range of software drivers and example code that you can use to write your own software or to use your PT-104A data logger with third party software. With the included Logging Software you can set the sampling interval from 1 second to several hours and set the maximum number of readings. You can also tell the PT-104A data acquisition module what do to when the temperature readings have been taken—either: stop; repeat immediately (start again); scroll (oldest recordings disappear); or repeat after delay (where the delay is set by the user). Multiple PT-104A modules can be used simultaneously with the logging software. Also, PT-104A modules can be mixed with TC-08 thermocouple input modules and used at the same time. Up to 20 units of any kind (PT-104A or TC-08) can be connected.Using the PT-104A logging software, data can be viewed in a spreadsheet and/or in a graph as it is being recorded. Data collected from previous recordings can also be viewed using the Player.

PT-104A Platinum Resistance Data Logger
    SensorPt1001, Pt1000N/AN/A
    Range-200 to 800°C
(-328 to 1472°F)
0 to 375 Ω1
0 to 10 kΩ
0 to 115 mV
0 to 2.5V1
    Linearity20 ppm20 ppm20 ppm
    Accuracy @ 25°C0.01°C120 ppm10.2%1
5 ppm/°C5 ppm/°C100 ppm/°C
    RMS Noise
    (Using Filter)
0.01°C10 ppm10 ppm
    Resolution0.001°C1 µ Ω0.156 µV
    Conversion Time
    Per Channel
720 mS
    Number of Inputs4
    Connectors4-pin mini DIN
    Input Impedance>>1 MΩ
    Overvoltage Protection±30V
    PowerPowered by USB or Ethernet:
USB 1.1: 5 V ±10% @ <100 mA
USB 2.0: 5 V ±10% @ <200 mA
Ethernet: 48 V ±20% @ <40 mA (<2W)
    Environmental20 to 30°C (68 to 86°F) for stated accuracy,
0 to 70°C (32 to 158°F) operating,
20 to 90% RH
    SoftwareLogging Software for 32-bit or 64-bit editions of Windows XP
(SP2 or greater), Vista, 7.
Software Development Kit containing drivers and example code for C,
C++, Excel and LabView.
    Ethernet PortConforms to IEEE 802.3 10Base-T.
Compatible with 10/100/1000Base-T networks.
Conforms to IEEE 802.3af Power-over-Ethernet (PoE).
    USB PortConforms to USB 2.0 full-speed (12 Mbps)
    Computer InterfaceUSB or Ethernet
    Dimensions36 H x 135 W x 184 mm D (1.42 x 5.31 x 7.24")
    Weight500 g (1.1 lb)
1 Quoted accuracy is for options marked

(Specify Model Number)
Part Number/Desc.
Availability: 1 week
4-channel RTD input data acquisition module
All prices on this site are shown in Philippine Pesos.
Note: Includes USB cable, ethernet patch cable, 4 mating mini DIN screw terminal connectors, quick start guide, Windows software and complete operator’s manual on CD.
Ordering Example: (1) PT-104A 4-channel RTD input data acquisition module, PHP62,112.02
We noticed you are from the US. Visit your local site for regional offers and live support.